Gorilla Waterproof Patch and Seal Spray White
Gorilla Waterproof Patch and Seal Spray White
Gorilla Waterproof Patch & Seal Spray is a flexible, rubberized coating that seals out water, air and moisture. The applicator nozzle has a controlled spray pattern providing a clean, even coat. Once applied, the self leveling formula smoothly covers small gaps and cracks ensuring a watertight seal. When dried, Gorilla Waterproof Patch & Seal Spray is paintable and temperature/UV resistant resulting in lasting repairs!
Sizes
PRODUCT FEATURES
- SEALS OUT WATER, AIR AND MOISTURE
- CONTROLLED SPRAY PATTERN
- FLEXIBLE
- PAINTABLE
- CREATES A PROTECTIVE COATING
- Temperature and UV Resistant
- USE ON: Roofs, Gutters, Skylights, Flashing, Chimneys*, PVC Pipe Joints, Windows, RVs, DIY Projects and More!
- GREAT FOR: Metal, Concrete, Wood, Aluminum, Brick, Tile, Fabric, Rubber**, Glass and More!
*For exterior use only. Not intended for inside of firebox or chimney stack.
**May not work for all types of plastics and rubbers
Not for continuous submersion or below-waterline use.
- Clean surface of dirt, dust, grease and oil. Make sure surface is dried completely.
- Shake well. Spray 8″ to 12″ from surface, covering evenly. A test spray on a disposable object is recommended before applying to your project.
- Apply multiple coats to ensure all cracks and holes have been filled. Allow to cure in between coats and before water exposure. Full cure at 24 hours.
NOTE: Test finished project with light water exposure to ensure all cracks have been filled. If test fails, apply additional coats. Do not use for gaps larger than 1/4.” Apply between 50° F and 120° F.
PAINTING: Works with both latex and oil based paints. When coating with oil based paints, use a primer first before painting.
TIP: To avoid possible clogging, turn can away from body towards a disposable object, turn upside down and spray a short jet of clear gas after completing job.
APPLICATION TEMPERATURE – 50°F- 90°F
SERVICE TEMPERATURE – -40°F to 160°F
INDOOR/OUTDOOR – Yes
UV/SUNLIGHT RESISTANT – Yes
PAINTABLE – Yes
FLAMMABLE– Yes
SOLVENT RESISTANT – No
We realize any DIY project may have a spill and we want to help you with tips and tricks to successfully remove glue from fingers and nails.
For bonded skin, please call 1-800-420-7186 to speak to a medical professional.
What surfaces will Gorilla Waterproof Patch & Seal Spray coat?
Gorilla Waterproof Patch & Seal Spray is designed to seal out water, air and moisture. Surfaces for use include, roofs, gutters, skylights, flashing, chimneys*, PVC joints, windows, RVs and other DIY projects. *Please note, this product is not intended for inside of firebox or chimney stack. It may not work for all types of plastics or rubbers.
Do I need to do anything special to the product before use?
Shake the can well. Once the marble inside the can is heard moving, shake for 30 seconds to get a good mix of the coating and propellant to ensure an even application.
How do I remove Gorilla Waterproof Patch & Seal Spray from my surface?
This material will be difficult to remove from a surface. For wet material, immediately wipe with a dampened rag. For cured material, a solvent may soften the material but could damage the surface around/underneath. Gently scrap the material to try and remove.
How do I remove Gorilla Waterproof Patch & Seal Spray from body/skin?
To remove Gorilla Waterproof Patch & Seal Sprays from your fingers and nails, we recommend following these steps:
1) For wet material, thoroughly wash affected area with warm soapy water.
2) For cured material, wash with soapy water to loosen coating.
Is Gorilla Waterproof Patch & Seal Spray food safe?
This product is not recommended for direct or indirect food contact and should not be considered food safe.
How should Gorilla Waterproof Patch & Seal Spray be stored?
Store in a cool dry location. After each use, turn the can away from the body towards a disposable object, turn can upside down and spray a short jet of clear gas. This will help avoid clogging for future uses.
